Visit our UK Site
Visit our USA Site
Visit our Asia Site
Description
Product Description
Developed from our direct involvement within the BTCC and Mini Challenge race series where we have provided race proven and championship winning cooling packages, we have directly transferred our knowledge from this over to our road going products. FMOC11 has been developed with the same engineering expertise that is applied to our Mini Challenge Oil coolers, these see extensive driving over the race season calendar, so we are proud to give the I30N the same motorsport treatment. Lowering your oil temps on and off the track whilst providing a product that does not skimp on quality, so much so that it is backed by our Forge Lifetime Guarantee*
With our extensive range of performance parts out on the market allowing the limits of the i30N/Veloster N to be pushed in the chase for top power gains, the addition of power and speed creates heat. Rising oil temperatures will result in only one outcome, a reduction of sufficient lubrication of your engines internal components. Therefore, the FMOC11 is a must have product for the keen driver, the location of the oil cooler radiator at the front of the vehicle’s radiator grill allows for superior air flow. During our development of this product we have seen oil temperatures reduced significantly.
The Hyundai oil cooler has its inlet and outlets placed in the correct position for optimum flow , when oil coolers are fitted upside-down this can lead to cavitation (air locks) within the system, this can over a prolonged period of time lead to engine fatigue and potentially internal component damage due to insufficient engine lubrication.
Unlike many oil cooler kits, the FMOC11 keeps the factory oil to water cooler in position. This essentially doubles your engines oil cooling. We’ve also developed the kit to use a bespoke laser cut aluminium bracket which makes for perfect fitment to the i30N crash bar. Supplied with the kit are 2x pre-assembled, high quality double braided AN-8 oil lines.
We’ve incorporated a thermostat that is built into the oil cooler sandwich plate, this has been set to open at 85C as this was observed to be the optimal working temperature of the oil cooler when testing, this means the engine is working at its most efficient oil temperature range however hard you push the vehicle.
The kit comes with the following:
1x Forge Aluminium sandwich plate
1x Twin pass oil cooler
4x M6x20 fasteners
4x M6 washers
2x Oil lines
4x M6 Rubber Riv nuts
1X M20x1.5 adaptor
All the fixings required
Check your vehicle compatibility: Click here
Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.
Associated Products
Product Reviews
Product Reviews
Be the first to review this product
Want to leave a review?
Login
Register FREE!
Compatible Vehicles
Instructions
Oil Cooler Kit for Hyundai i30N
Warranty
10 Year Warranty Information
The majority of Forge Motorsport products come with a limited 10 Year Warranty (brakes pads excluded). All warranty claims must be accompanied by the original proof of purchase to enable us to help you. Failure to supply this proof will result in your claim or enquiry being denied.
For further information, please call our customer service team on +49(0)3222/1097-308 or email info@forgemotorsport.eu.
Do not use aggressive (acidic) car cleaning products, particularly traffic film remover solutions or shampoos to clean your intercooler, radiator, or oil cooler. The use of these products can damage Forge Motorsport cooling systems and invalidate your warranty. These are often found at car washes. A light, warm, soapy solution (free of harsh acidic cleaning compounds) should be used to clean you cooler and thoroughly rinsed away. We recommend that you should inspect your product on a regular basis for bent and/or crushed fins. Any bent fins should be carefully straightened to allow ambient air to pass through the core face. At the time of installing your Forge radiator, an approved coolant must be used and added to the coolant system. Be sure you never mix coolant and always use distilled water.
This warranty does not apply to any defect in the goods arising from fair wear and tear, wilful damage, accident, negligence by you or any third party, use otherwise than as recommended by the supplier, failure to follow the supplier’s instructions, or any alteration or repair carried out without the supplier’s approval.
Shipping
European Shipping
We ship to selected EU countries as displayed during the checkout process.
Delivery service charges will vary depending on the quantity of product ordered, the related parcel size, and your destination.
Our shipping methods ensure safe and timely delivery of your new Forge products. For further information on cost and delivery times, please contact us if you require any more information via our contact page.
We reserve the right to change the delivery service and our shipping providers at any time.
Once a product has left our warehouse and is in the possession of the shipping company, any claims must be made directly with that shipper, however we may be able to assist in some cases.
FAQ's and other info can be found here.
Manufacturer & EU Contact Details
Manufacturer
Company Name: Forge Motorsport
Address: Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU, United Kingdom
E-Mail: info@forgemotorsport.co.uk
Phone: +44 1452 380999
EU Responsible Person
Company Name: Milltek Sport GmbH
Address: Gottlieb-Daimler-Str. 1-3, 53520 Meuspath
E-Mail: info@millteksport.de
Phone: +49 (0) 3222 1097308
Expert Answers
Hello, is the oil radiator compatible with the DCT versions? (there is already a specific radiator for the automatic gearbox there) thank you
Hello
Yes this product NOT is compatible with the DCT version I30N.
The product you need is the FMOC13.
Regards
This is only for pre FL, is there a version for FL or any instructions if it can be used?
Hello , this will fit pre and post facelift , the installation instructions can be found on the product page under the instructions tab.
Good afternoon, Could you please tell me the characteristics of the oil cooler. With a box. Weight, length, width, height.
Hi Arsen, the details you require are as follows:
52x30x27cm
6kgs
